- Model type
- Shipping unit
No copper-based metal is used for the metal material. *Some products are only compatible in the flow path.
HNBR or FKM is used for the seal rubber material. *Some products are only compatible in the flow path.
No lubrication is used during assembly.
Fluorine grease is used as grease, and the product is packaged in a clean room after cleaning with clean air.
Outline Dimensional Drawing
* Reference value for height dimension after tightening thread.
|Fluid medium||Air, Water, Others such as chemicals (Conditional*)|
|Max. operating pressure||0.9MPa（at0～20℃）|
|Operating temp. range||0～80℃（No freezing）|
* Make sure to follow the instructions below when the fluid medium is water or liquid.
Surge pressure must be controlled lower than max. operating pressure when using water or liquid as a fluid medium.
Tap water in Japan free from foreign substances or contamination can be used. Carry out the evaluation under an actual operating condition for using other kind of water.
Be sure to place Insert Ring (WR) into the tube edge when using water or liquid as a fluid medium.
The specification above may not be applied, depending on the kind of chemicals or mixed gases used as fluid medium. Make sure to use PISCO products after verifying their suitability on the user side.
One-touch mechanism contributes to easy fitting of tubes.
There is no need to worry about rust and metallic ion because the fitting is all-plastic made.
It is compatible with special specifications.
Sealing material can be change from standard FKM to EPDM or NBR depending on applications.
2 types of package are available.
Standard package and clean-room package that products are washed by clean air, then packed in ISO class 6 cleanroom are available.
Since it conforms to the Food Sanitation Act (only FKM spec.) and has completely oil-prohibited specifications, it is best suitable for food-related applications.
The weight is about 1/3 that of standard fitting, and 1/5 that of SUS316 compression fitting.
Products with Different Options
Products with Different Sizes
Detailed Safety Instructions
1.Check chemical resistance before using the products, when the fluid medium is chemicals, solvent or mixed gases. Depending on the conditions, it may cause damage to the products, the escape of tubes, and a fluid leakage.
2.When the fluid medium is water or liquid, do not use fittings unless the operating environment meets all the described specifications in the catalog. Otherwise, it may cause damage to the products, the escape of tubes and a fluid leakage.
3.This series has seal rubber material options, but there is no way to identify between each material. Store each product properly not to mix up, after opening their packages.
1.PPS resin has a characteristic of color change by being exposed to sunlight, fluorescent light, mercury lamp, high temperatures and etc. for a long term. There is no problem on the product performance for the color change.
2.Taper thread is not coated with Sealock. When coating the thread with seal tape or sealant, do not coat 1.5 to 2 screw ridges from the tip of the thread. See below figure..
3.Tighten taper thread by hand until it stops, then use a spanner to tighten it about 2 or 3 more turns. Excessive tightening may break the thread part. Inadequate tightening may cause a loosened thread or a fluid leakage.
4.Resin type taper thread may have a fluid leakage or get loosened caused by “creep phenomena”, due to a long term use of the thread. Check the tightening condition periodically and re-torque the thread in case of leaks. If re-torque of the thread does not solve a leakage problem, change it to a new product.
5.Due to the resin-made collet, there is a possibility that the hard type tubes and the stem type of non-Chemical Series may have a problem of escape. Verify the matching of connections before using the products.
7.Tube insertion into this product is tighter than that of Tube Fitting Standard Series due to its oil-free specification. Make sure to insert tube up to tube end. When inserting a tube, put a liquid like water on the tube, which does not affect the product and the tube. It will improve the smoothness of tube insertion.
8.The seal rubber material EPDM is not suitable for general air pipings, due to its inferior durability against mineral oil.
Inquiries about this product
It is also possible to suggest products suitable for various conditions such as applications and functions. Please feel free to contact us or visit the nearest sales office.
The following are frequently asked questions. Please check before making inquiries.
Fluoropolymer (PFA) Tube
Superior chemical and weather resistance makes Fluororesin Tube best suited for chemical, food-processing, medical care and semiconductor applications. Color:5 colors, Size 12 sizes including Inch O.D.
Fluoropolymer (FEP) Tube
Compared to our SFT tube, we successfully reduced the cost by 44% average. Color:5 colors, Size:12 sizes including Inch O.D.
Polyamide Tube, which satisfies the Food and Additives Standard in Japan, can be used for food processing. Color:1 color, Size:9 sizes